木屑顆粒機模具的好壞不只是模具不耐磨這一個壞處，模具容易爆模，更換頻率提高，勞動強度增加，因此選擇合格的木屑顆粒機模具，是節約成本提高生產效率，最有效地途徑。

Sawdust particles machine mould quality not only mould don't wear this one disadvantage, mould easily burst mode, change the frequency increase, increase the intensity of labor, so choose qualified sawdust particles machine mold, is to increase the production efficiency, cost saving is the most effective way.

木屑顆粒機環模通常由碳鋼或不銹鋼資料經鍛壓、切削、鉆孔、熱處理等工序制成。

Sawdust particles machine ring die are usually made of carbon steel or stainless steel material by forging, cutting, drilling, such as heat treatment process is made.

一、環模所用的材料和每個加工工序對其運用壽命及制粒質量、產值有直接的影響。

A, materials used in the ring die and each processing procedure for its using life and granulating quality, output has a direct impact.

因而，選購環模時，必定要選用技能過硬，有必定規劃的廠家。若是隨意選用技能設備落后的小廠，在出產過程中肯定會呈現這樣或那樣的疑問（比方環模不出料、商品顆粒表面粗糙、爆模等）。其次，?？椎难心ヒ彩欠浅Ｖ匾模S家由于設備技能約束，主要靠人工進行拋光，經常呈現漏拋表象，或許達不到所需求的光潔度。因而這樣的環模，在實際生產過程中也是將難以，即使出料，也會構成顆粒表面粗糙和塞機表象。所以用戶們應在秸稈顆粒機的環模質量方面把好關。

Therefore, when the choose and buy ring die, must choose superior skills, some have planning manufacturers. If small plant of optional choose skills, poor equipment, will appear in the process of producing this or that questions (for example loop die not discharging, commodity grain surface is rough, detonation mode, etc.). Secondly, die grinding is also very important, the small manufacturer skills constraints due to equipment, mainly by manual polishing, often appear behind appearances, leakage may not meet the requirements of finish. Therefore the ring die, will not be in the actual production process, even if the material, will constitute a rough surface particles and machine surface. So users should be in the straw quality of ring die pellet machine, the better off.

二、合理選擇模具的厚度

Second, the reasonable choose the thickness of the mould

正確選用適宜的模具厚度是確保商品質量和產值的一個重要環節，它涉及到一個壓縮比問題（壓縮比=?？子杏瞄L度／模孔直徑）。壓縮比大的環模，其構成的顆粒密度大，表面光潔。否則，所產顆粒外觀松懈，造成秸稈顆粒含粉率高。但壓縮比若是過大，會令環模難于出料，以致?？锥氯?針對出產含纖維比高的物料，環模壓縮比應相對取小些，或用舊模出產。

Right to choose the suitable thickness of mould is to ensure the quality and output of an important link, it involves a question of compression ratio (compression ratio = die useful length/die hole diameter). Compression ratio of ring die, its form grain density is big, the surface is bright and clean. Otherwise, particle appearance from the lax, straw particle high powder content. If the compression ratio is too big, can make ring die hard to discharge, so that the die hole plug. To produce fiber material than high, ring die compression ratio should be relatively small, or use the old mould produce.

三、調好木屑顆粒機壓輥和環模間的相互合作

Third, adjusted the sawdust pellet machine mutual cooperation between the roller and ring die

如果壓輥和環模的空隙調整是不是合理，直接影響木屑顆粒機的作業狀況。間距過大，則由于環模和壓輥之間的擠壓力不足以戰勝物料經過?？椎哪Σ亮Χ斐啥氯?。過小則易損傷環模及壓輥。所以若要把握好合理的間距，需要靠顆粒工經過長時間的出產實踐和仔細探究才能做出正確的調整。這里有些環模與壓輥的適應經驗和大家分享下，即是新模配新輥，一對壓輥固定一個環模合作運用。這樣，就可避免新模配舊壓輥，或許舊模配新壓輥等表象，以免造成新壓輥或是新模具的磨損。從而間接進步和延伸環模、壓輥的運用壽命，減少生產成本。

If press roller and the ring die gap adjustment is reasonable, directly affect the sawdust pellet machine operation condition. Spacing is too large, because the ring die and roller pressure between the extrusion pressure is not enough to overcome the friction material through the die and cause clogging. The small ring die and roller is easy to damage. So if you want to grasp the reasonable spacing, need to rely on grain work after a long time production practice and explore to make the correct adjustment. Here are some ring die and roller to adapt to experience and share, namely the new roller is matched by a new mould, a pair of roller fixed using a ring die cooperation. In this way, can avoid the mold with old roller, perhaps the old mould with the new roller surface, so as not to cause new roller or new mould wear and tear. Indirect progress and extension ring mold, the use of the roller life and reduce the cost of production.

四、做好木屑顆粒機環模的保護工作

Four, to do a good job of the protection of the sawdust particles machine ring die

一個環模運用作用好與壞，除自身技術質量決議外，肯定離不開環模的保護。由于在出產過程中，一個環模必定會有阻塞、磨損現象，這樣的環模，若是不進行必要的保護保護，必然構成產值下降，能耗增大，乃至壓不出料，呈現堵機表象。因而，有上述表象發作時，有必要對環模進行一系列的保護作業。

A ring die use effect is good or bad, in addition to their own technological quality resolution, certainly cannot leave the ring die protection. Because in the process of produce, to have a ring die block, wear phenomenon, so the ring die, if you are not necessary protection protection, necessarily constitute output drop, increase of energy consumption, and not discharging, rendering machine. Therefore, there is the surface occurs, it is necessary to ring die the protection of a series of operations.

五、木屑顆粒機模具的修復使用

Five, sawdust pellet machine mold repair use

木屑顆粒機的成型需要模具和壓輪皮做出犧牲,由于木屑顆粒成型難，必須有強大的力量才能夠使顆粒成型,如此必然造成模具的磨損。根據以往經驗，我們并不支持廠家進行模具的修復。因為修復模具,無非是增大孔的錐度。但是,在修復中也會造成淬火的硬度受損,以至于修復后很短時間內就會磨損到出粉率高、不成形、密度小、溫度低這個狀態。修復所產生的費用能否抵負生產的成本也是我們需要慎重考慮的問題。所以廠家在出現模具損壞的情況，最好是添置新的模具，以免在后續的生產中問題的出現。

Sawdust particles forming die and roller skin to make sacrifices, because sawdust particles molding difficult, must have a powerful force to make particles forming, so inevitably cause mould wear and tear. Based on past experience, we do not support manufacturer for mold repair. Because the repair mold, is nothing but increase the taper hole. But also can cause the quenching hardness in repair damaged, that within a very short time after repair will wear into the flour extraction rate is high, not forming, small density, low temperature of the state. Costs of repair will justify the cost of producing negative is the problem we need to carefully consider. So manufacturers, in the case of a mold damage, it is best to add the new mold, in order to avoid problems in the subsequent production.

恒星顆粒機小編，今天就為大家介紹到這里，需要更多了解可以直接電話聯系我們15650569708.

濟南恒星新能源有限公司專業生產木屑顆粒機、木屑烘干機、木屑粉碎機、木材破碎機、顆粒冷卻機、顆粒包裝機等生物質顆粒機生產線更多產品登錄：onqqwes.cn